![]() The power led will stop blinking and go steady and the wireless led will finally come ON. Wait 5 minutes and during that time, look at your router.Power cycle the router, and as you see your PC's LAN connection pop in, run the tftp.exe as prepared in the step above.Now, give your PC a static ip address (192.168.1.x).At this point, I used "tftp.exe" (included in the GV5Flash.zip) and prepare that for flashing using the included "dd-wrt.v24-12548_NEWD_micro.bin" firmware.I get the same "problem" as in the beginning only now I cant get back to management mode. I wait 5 full minutes (just in case), then power cycle the router.I wait 5 full minutes (just in case) then, still in "management mode", I use the "My54gImage.bin" created with the ""VXImgToolGui.exe"" tool and run the upgrade again.Now, In management mode, I used the "vxworks_prep_03.bin" file to attempt to upgrade firmware since I am unable to do so logged in to router because the router wont boot.According to this wiki, it is advised to run "VXImgToolGui.exe" in order to save your MAC address so that's the first thing I did.DHCP now running, but now the router is in "management mode" at 192.168.1.1, my PC was issued 192.168.1.11.as a result of this, I am unable to follow the steps outlined above concerning GV5Flash.zip.cycle power several times to see if it would change.Steps taken to revive it with dd-wrt firmware: Problem: power led blinking rapidly, wireless led is off, my PC is unable to get an ip address by way of DHCP. PROBLEM AND WORKAROUND TO AN INACCESSIBLE LINKSYS WRT54G V6.0 ROUTER- may be good for V5 as well. Reset your computer Ethernet connection to auto IP and auto DNS.When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another HARD reset on the router.When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.Try using a different browser as well, to navigate to 192.168.1.1. If you still don't get success, clear your browser cache. If you don't get success, repeat from steps 20(4) up to this one.When you get a success, wait FIVE FULL minutes.Select the 12548 Newd_Micro.bin firmware.Enter 192.168.1.1 as the address in the top box of tftp.exe.Wait for the "Upgrade Success" message, and then WAIT FIVE FULL MINUTES again.Select the My54gImage.bin file that you created.NOW you should be in the MANAGEMENT MODE window. If you get a blank window, clear your browser cache. When five full Earth minutes have passed, power cycle the router.Don't you TOUCH that router for FIVE MINUTES. Navigate to the folder that you are using, and select vxworks_prep_03.bin. ![]() Go to Administration and Firmware Upgrade.Enter "root" as the username and "admin" as the password.If you see management mode, power cycle the router again. You should open the linksys webgui and NOT a page that says Management Mode. Open your browser to 192.168.1.1 by putting that in the browser address window of your browser.Power cycle the router (unplug the power from the router for 30 seconds and then plug it back in).Click on the three dots next to "output image" and save the file as My54gImage.bin in the same folder as everything else is located.Put the MAC address from the bottom of your router in the box that says "Desired MAC" (Tip: You can also copy/paste the mac address from the Linksys Firmware Status\Local Network page).Make sure the top button is on the left for WRT54G, not the right for WRT54GS.Unzip the VXImgToolGui.zip file to the same folder as where you placed the other files you downloaded.Unzip the file you downloaded in step one, and place it in a location you can easily find on your computer.Turn your firewall and any wireless computer connections OFF. Nothing should be connected to your computer or the router except the LAN cable between them. Connect the LAN cable from your computer to a LAN port of your router.Set a static IP on your computer to 192.168.1.7.Do a HARD reset on the router according to note 1 of the peacock announcement (30/30/30).Read the peacock announcement found here:.The file is clean and contains no malware). Go to this thread and download the zipped files in GV5Flash.zip: (If you get a malware warning from your antivirus, ignore it.If you don’t you will get a generic MAC address on your router and a generic MAC address will mean most ISP won’t let you connect to the Internet. IN SPITE OF SOME OTHER INSTRUCTIONS ELSEWHERE, YOU REALLY NEED TO CREATE A CUSTOM VX Image for your router. NOTE: During configuration or flashing a router, the only thing that should be hooked to the router is the computer through the ethernet cable, and power.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |